Comparison of Trial Restoration Matrix Fabrication Methods
NCT06912503 · Status: COMPLETED · Type: OBSERVATIONAL · Enrollment: 20
Last updated 2025-04-04
Summary
This observational analytical in vivo study aimed to assess the dimensional accuracy of diagnostic trial restorations fabricated through four different techniques: condensation silicone matrix without external shell, addition polyvinylsiloxane (PVS)-silicone matrix with an external resin-based shell, transparent addition PVS-silicone matrix with an external vacuum shell, and a CAD/CAM combination matrix.
Methods: Patients (n=20) in need of anterior upper teeth aesthetic rehabilitation were recruited. Clinical and radiographic examinations, intraoral scanning, and dental CAD software were used to design a virtual diagnostic waxing. A 3D printed waxed cast was obtained, and four different matrices were fabricated. Trial restorations were performed using calibrated materials, and intraoral scans were taken for each restoration. Linear and volumetric discrepancies were evaluated using reverse engineering alignment software
Conditions
- Teeth Restoration
Interventions
- DEVICE
-
Device to deliver trial restoration matrix
Auto-polymerization bisacrylic material (Luxatemp Star, DMG) was used to perform the trial restoration for condensation silicone matrix, addition PVS-silicone matrix with external resin-based shell and CAD/CAM combination matrix. Light-cured flowable composite-resin (Filtek Flow, 3M Dental Products) was used to perform the trial restoration for transparent addition PVS-silicone matrix. The rationale behind using different material stands on the material selection usually chosen by clinicians for each matrix. In the same appointment 4 trial restorations were performed to each patient using the four different matrixes.
Sponsors & Collaborators
-
Universitat Internacional de Catalunya
lead OTHER
Principal Investigators
-
MIGUEL ROIG CAYON, MD, DDS · Universitat Internacional de Catalunya
Eligibility
- Min Age
- 18 Years
- Max Age
- 70 Years
- Sex
- ALL
- Healthy Volunteers
- Yes
Timeline & Regulatory
- Start
- 2023-01-08
- Primary Completion
- 2023-06-22
- Completion
- 2023-11-03
Countries
- Spain
Study Locations
More Related Trials
-
10 Years Evaluation of Composite Restoration
NCT02764450 ·Status: COMPLETED ·Phase: NA
-
Clinical Evaluation of CAD/CAM vs. Conventional Veneer Restorations
NCT06969911 ·Status: NOT_YET_RECRUITING ·Phase: NA
-
Retrospective Study on Clinical Performance of Screw-retained Implant Crowns
NCT04370314 ·Status: COMPLETED ·Phase: NA
-
Vital and Non-vital Posterior Teeth Restored With Onlays and Single Crowns Using Three Different Restorative Materials.
NCT07259265 ·Status: COMPLETED ·Phase: NA
-
Investigation of Bacterial Adhesion and Bactericide Effect ex Vivo on Different Implant Restoration Materials
NCT04657757 ·Status: COMPLETED ·Phase: NA
-
Dimensional Changes of Peri-implant Tissue in Immediate Implants With Individualized Healing Abutments
NCT06455436 ·Status: RECRUITING ·Phase: NA
-
Guided Bone Regeneration of Peri-implant Defects Comparing Submerged Versus Non-submerged Healing
NCT03900741 ·Status: UNKNOWN ·Phase: NA
-
Resin-Cement Type Influence on Cement Remnants in Implant-Supported Restorations
NCT06711237 ·Status: COMPLETED ·Phase: NA
-
Implant/Abutment Module Stability of Original vs Compatible Connections
NCT03524872 ·Status: UNKNOWN ·Phase: NA
-
Prosthetic Outcomes and Clinical Performance of Implant Supported Zirconia Crowns
NCT06417632 ·Status: NOT_YET_RECRUITING ·Phase: NA
-
Esthetic Outcome of 3D Printed Hybrid Ceramics as Final Restorations for Single Screw Retained Implant.
NCT07154602 ·Status: NOT_YET_RECRUITING ·Phase: NA
-
One-abutment One-time for Immediate Restoration Procedure in the Esthetic Zone
NCT04139512 ·Status: COMPLETED ·Phase: PHASE4
-
Digital Analysis of Occlusal Force Distribution in Single-Tooth Implant Restorations
NCT06862973 ·Status: COMPLETED
-
Comparison of Conventional and CAD/CAM Dental Restorations
NCT02494427 ·Status: UNKNOWN ·Phase: NA
-
Clinical Evaluation of Chairside CAD/CAM Nano-ceramic Restorations
NCT01464294 ·Status: TERMINATED
-
Evaluation of CAD/CAM Onlays Fabricated by Subtractive Versus Additive Digital Manufacturing Techniques.
NCT05943782 ·Status: ENROLLING_BY_INVITATION ·Phase: NA
-
Comparative Evaluation of Implant Stability, Soft & Hard Tissue Healing Around UV Activated vs Conventional Implants
NCT06541912 ·Status: RECRUITING ·Phase: NA
-
Dimensional Accuracy of Complete Denture With Rapid Prototyping and Conventional Method
NCT03119753 ·Status: UNKNOWN ·Phase: NA
-
Comparison Between Conventional and Digital Workflow in Dental Prosthesis
NCT06215781 ·Status: COMPLETED ·Phase: NA
-
Post-retained Restorations for RPD Abutments
NCT03466437 ·Status: UNKNOWN ·Phase: NA
-
Comparing Cobalt-Chromium Versus PEEK Secondary Telescopic Crowns on Implant Retained Mandibular Overdenture.
NCT06637930 ·Status: COMPLETED ·Phase: NA
-
Stereolithographic Technique for Dentures
NCT02911038 ·Status: COMPLETED
-
Clinical Influence of Different Surface Treatments on Implant Stabiity
NCT06808724 ·Status: RECRUITING
-
Clinical Performance of Incremental and Bulk Fill Composites in Class II Restorations
NCT02889835 ·Status: COMPLETED ·Phase: NA
-
Implant Retained Rehabilitation With Surgical and Prosthetic Digital Workflow
NCT04066309 ·Status: ACTIVE_NOT_RECRUITING ·Phase: NA