Clinical Performance of Different Adhesive Strategies With a Universal System in Sclerosed Dentin in NCCL: A Double-blind Randomized Clinical Trial.

Summary

The aim of this randomized, prospective, parallel, double-blind clinical trial will be to evaluate the clinical performance of restorations performed in non-carious cervical lesions (NCCL) using a soft ph universal adhesive system, varying the adhesive strategy (self-etching vs. selective etching of the enamel) and the sclerosis characteristics of the dentinal substrate over 24 months.

Conditions

• Sclerotic Dentine
• Non Carious Cervical Lesion

Interventions

PROCEDURE

Composite resin restoration with Self Etch adhesive protocol and absence of sclerotic dentin

The adhesive system Single Bond Universal (3M Oral Care; Brazil) and a nanoparticulate composite resin Z350 XT (3M Oral Care; Brazil), shade A3B, will be the materials used in the restorative procedures. For the D-SE group, the universal adhesive system will be applied with a disposable microbrush, actively, for 20s and then a gentle stream of air will be used for 5s to solvent evaporation, followed by light curing for 10s using the Valo Cordless light curing (Ultradent Products Inc.), in Standard mode (1000mW /cm2). All groups will receive the restorations made following the incremental technique of insertion of composite resin (2mm per increment), which will be light cured according to the manufacturer's recommendations.

PROCEDURE

Composite resin restoration with Seletive enamel etch adhesive protocol and absence of sclerotic dentin

The adhesive system Single Bond Universal (3M Oral Care; Brazil) and a nanoparticulate composite resin Z350 XT (3M Oral Care; Brazil), shade A3B, will be the materials used in the restorative procedures. For the D-SELETIVE group a 37% phosphoric acid will be applied only at the enamel margin for 15s, then rinsed with water for 20s, and slightly dry. The universal adhesive system will be applied with a disposable microbrush, actively, for 20s and then a gentle stream of air will be used for 5s to solvent evaporation, followed by light curing for 10s using the Valo Cordless light curing (Ultradent Products Inc.), in Standard mode (1000mW /cm2). All groups will receive the restorations made following the incremental technique of insertion of composite resin (2mm per increment), which will be light cured according to the manufacturer's recommendations.

PROCEDURE

Composite resin restoration with Self Etch adhesive protocol and presence of sclerotic dentin

The adhesive system Single Bond Universal (3M Oral Care; Brazil) and a nanoparticulate composite resin Z350 XT (3M Oral Care; Brazil), shade A3B, will be the materials used in the restorative procedures. For the SD-SE group, the universal adhesive system will be applied with a disposable microbrush, actively, for 20s and then a gentle stream of air will be used for 5s to solvent evaporation, followed by light curing for 10s using the Valo Cordless light curing (Ultradent Products Inc.), in Standard mode (1000mW /cm2). All groups will receive the restorations made following the incremental technique of insertion of composite resin (2mm per increment), which will be light cured according to the manufacturer's recommendations.

PROCEDURE

Composite resin restoration with Seletive enamel etch adhesive protocol and presence of sclerotic dentin

The adhesive system Single Bond Universal (3M Oral Care; Brazil) and a nanoparticulate composite resin Z350 XT (3M Oral Care; Brazil), shade A3B, will be the materials used in the restorative procedures. For the SD-SELETIVE group a 37% phosphoric acid will be applied only at the enamel margin for 15s, then rinsed with water for 20s, and slightly dry. The universal adhesive system will be applied with a disposable microbrush, actively, for 20s and then a gentle stream of air will be used for 5s to solvent evaporation, followed by light curing for 10s using the Valo Cordless light curing (Ultradent Products Inc.), in Standard mode (1000mW /cm2). All groups will receive the restorations made following the incremental technique of insertion of composite resin (2mm per increment), which will be light cured according to the manufacturer's recommendations.

Sponsors & Collaborators

• Universidade Federal do Para

  lead OTHER

Principal Investigators

• Cecy M Silva, PhD · Universidade Federal do Pará

Study Design

Allocation

RANDOMIZED

Purpose

TREATMENT

Masking

DOUBLE

Model

PARALLEL

Eligibility

Min Age

18 Years

Sex

ALL

Healthy Volunteers

Yes

Timeline & Regulatory

Start

2021-07-27

Primary Completion

2022-03-30

Completion

2023-12-30

Countries

• Brazil

Study Locations